In this video we'll demonstrate how to:
Please visit our website for more information on this topic.
To skip ahead, use the annotations located at the bottom of the screen.
If there is old or unwanted floor marking tape or painted lines that need removing-use a flat-edged paint scraper or putty knife. Remove tape by chipping away at each corner of a line. A heat gun can be used if a paint scrapper alone is ineffective and a non-citrus based degreaser will remove all leftover adhesive residue.
The first step in successful installation of PathFinder tape is to ensure that the application area has been properly cleaned and dried. A dry, clean application surface allows for the tape's adhesive to cure completely. After clearing dust and debris-use a non-citrus based de-greaser on any tough stains or oily spots on the floor. Then, mop the area with warm soapy water. Leave time to dry and you're all ready to apply PathFinder floor marking tape.
There are no exact regulations for floor marking, so the first rule of thumb is to stay consistent.
In this example, we will be using PathFinder Rigid Tape designed for long term industrial use to create a line six inches from the storage rack. Measure out your beginning and end points using a ruler or tape measure. Then, using a chalk, laser or reference line, following the intended path to assure straight application.
Remove the adhesive liner at the beginning of the roll and apply approximately 10 to 12 inches of tape to the floor. Smooth the tape out and apply even pressure to ensure a strong adhesive bond.
Following the reference line and applying light tension, begin to remove the adhesive liner in sections approximately 3 to 5 feet at a time and begin to install the tape. Applying in short sections allows for the accurate installation, no wasted tape and helps avoid bubbles or creases. Continue this process until the job is done.
Once PathFinder tape has been successfully installed, allow 24 hours for the adhesive backing to fully cure before putting it into use.
Make sure the application area has been properly cleaned. This involves making sure there are no oily areas, dust or dirt.
Remember that there are no exact regulations for floor marking, so staying consistent is key. In this example we'll be using PathFinder hazard stripped Flex tape.
Link to Hebei Top Tape
Use the frame of the doorway as the guidelines. After aligning with a T or square to ensure accurate angles, place PathFinder tape on either side of the door frame, creating perpendicular lines. Then, if the door swings in, find the maximum distance the door will swing, if it swings out- simply select the desired distance and lay the cross piece down. Create two 90 degree corners at the intersections and smooth out the remaining end pieces. If you need assistance creating corners using PathFinder- follow the link.
And with that, your doorway is safely designated- alerting workers to keep an exit way clear or to beware of constant traffic.
If you have any questions or need help with a unique labeling challenge; you can speak with one of our customer service specialists. Our service hours are 5:30 a.m. to 4 p.m. Pacific Standard Time, Monday through Friday. Call us at 1-888-326- or to can chat live online just go to floormarking.com.
Installing industrial floor tape is a surprisingly easy process, and one that can be completed without any need to shut down a facility. When done properly, the tape will be securely attached to the floor so it can remain in place for years without any trouble. The following instructions will help ensure the installation process goes smoothly.
The first, and perhaps most important, step is to plan out where you need the tape to be applied. Planning out where you need floor markings, what color they need to be, and anything else that is needed will help ensure the installation only has to be done once. While it is not terribly difficult to remove tape that was placed in the wrong area, it is always best to only have to do things once.
Floor marking tape should be applied to a clean floor. Washing the floor using whatever normal process is followed in your facility, and then allowing it to dry, will make it so the floor markings can properly stick. The floor doesn&#;t have to be absolutely spotless, but simply get all excess dirt, dust, and debris out of the area so the adhesive can form a strong bond with the flooring itself.
The actually application of the floor tape is likely the step that is going to take the longest. For floor marking shapes or small pieces of tape, simply begin peeling off the protective coating from the adhesive side, and slowly apply it to the floor. Attempt to start from one edge and evenly move toward the other side so that there aren&#;t any wrinkles or air bubbles.
If you&#;re applying long pieces of floor marking tape it is best to use a floor marking tape installation tool. This tool will roll out the tape onto the floor in a very straight and even way. It also applies some pressure along the way so it won&#;t get pulled up as you move along. The only real challenging part of this process is applying the beginning of the roll to the floor so that it is secured in place and will roll out in the direction that is needed.
Once the floor markings have been applied to the floor it is best to apply pressure along the length of the tape to ensure the adhesive is able to properly take hold to the flooring. In most cases simply walking along the tape will be more than sufficient to ensure the tape will be secured in place and will last long into the future.
For more PVC Floor Marking Tapeinformation, please contact us. We will provide professional answers.