As manufacturing progresses through the 21st century, stamping manufacturers keep on searching for a better mousetrap that will help them be more efficient and effective today and in the future.
When you are looking at purchasing a new press and are trying to decide between an eccentric-gear or link-drive mechanical press or a servo mechanical press, many things must be taken into consideration. You should first look at what types of materials are being stamped and the run times needed. Considerations might involve tight tolerances and the complexity of the parts. Your operation might require more automation than you have, or remote operation. Perhaps the most important factor is cost and your budget.
While a place for traditional mechanical press technologies will exist in this new age, servo technologies are starting to become more of a necessity for certain stamping manufacturing operations. In other cases, a mechanical press will do the job well. Both standard mechanical and servo press technologies offer benefits in future press shops.
Materials. As the world pushes more toward electric vehicles and renewable energy, high-strength, advanced, and exotic materials are becoming more prevalent in manufacturing processes.
No matter how big or small your shop is, if you are running simple, cold-rolled steel, aluminum with a Class II or Class III surface requirement, or high-strength steels up to 950 MPa, then you might want to look first at a modern standard mechanical press.
Part Complexity. Whether you are stamping flat parts or adding a small draw to the material with accompanying concerns about springback or breakthrough shock, a new mechanical press could be the way to go.
Speed. Mechanical presses are the fastest for applications requiring full torque at maximum speeds. Servo presses are equipped with mechanisms to gain speed, but for long runs and simple parts, mechanical presses have a speed advantage.
Cost, Budget, ROI. Finally, and not the least important (especially from a purchasing point of view) is the price of your new press. Currently, mechanical presses are still cheaper to purchase than a servo press. That can be a huge benefit to your bottom line in the short run.
If you don&#;t need the extra flexibility of a servo press, you are stamping relatively basic parts, and the part families that you are running are all the same or very similar, then a servo press may not gain you a good return on investment (ROI).
Materials. For operations that are stamping high-strength materials above 950 MPa or other specialty steels, Class I surfaces, or multiple jobs requiring several die changes per day, then adding a servo press to your fleet of presses is recommended.
Part Complexity. If you are stamping multiple different part families in which a large variation in the press curve is required, then a servo press offers the flexibility to get this done. By having control of not just the downstroke but also the dwell time at bottom dead center, and being able to accelerate on the upstroke, you can speed up the operations. One of the big benefits of a servo press is to be able to preprogram specialty curves for multiple part families with different strokes. In that way, a servo press provides definite advantages that a link-drive press does not.
Speed. A servo press offers better control of the ram speed. This is especially important when stamping the specialty materials that are used today for the new generations of vehicles.
Cost, Budget, ROI. Yes, servo presses and the large servo motors they are equipped with are more expensive. Yes, you will be looking at different and potentially more expensive die technologies, and, yes, a specific type of training is required for your workforce to run a servo press properly. However, based solely on the advanced materials that are coming onto the market coupled with the need for a higher throughput, a servo press can be worth the higher initial purchase price.
For more information, please visit S-T Intelligence.
Tolerances.
Many new parts are requiring tighter tolerances. Either a next-generation mechanical press or a servo press can give you the tolerances that you are looking for.Many new parts are requiring tighter tolerances. Either a next-generation mechanical press or a servo press can give you the tolerances that you are looking for.
Automation. A factor that you should take into consideration when deciding on a new press purchase is the automation technology. Whether you decide on a mechanical or servo press, automation will help you increase your throughput.
It is very important to make sure that the automation technologies, such as a coil feeder or transfer equipment, can keep up with your press. It does no one any good if you purchase the latest and greatest press technology with a press that can go 60 to 80 strokes per minute (SPM) while the automation can only handle 30 SPM. Remember, the most expensive part of your investment is your press, and if anything is going to be the bottleneck, it should be the press and nothing else.
Dies. It is also important to note that the die technology will have to be changed and upgraded for a servo press if you are now running at a faster rate. This is common sense. Look for better-quality die materials, different types of coatings, or upgrade to nitrogen springs to your dies if you accelerate your operation. You won&#;t achieve the speeds you need if you use existing dies from presses that go 20 SPM in a press that goes 40 SPM. That is a recipe for disaster. Don&#;t expect those dies to last.
Whether you decide on a mechanical or servo mechanical press, common sense must prevail. A new press will help you improve your SPM, as long as you make sure that your dies and automation equipment can match the new speed requirements. That is essential to your envisioned new press output needs as well as improving your ROI.
1. How does available tonnage from a servo-drive press differ from that of a mechanical-drive press?
Since the motion of a servo press is programmable, some users wrongly believe that the tonnage available through the full stroke of the press is like that of a hydraulic press. However, servo presses have a mechanical drivetrain (eccentric gear or shaft); therefore, the tonnage curve basically will be the same as with a mechanical press. Stampers must review the press&#; tonnage curve vs. the specific applications in regard to loads higher in the stroke.
2. How does available energy relate to speed on a mechanical press?
The available energy of a mechanical press relates to the square of flywheel velocity. Typically, at one-half of the maximum press speed, available energy will begin to drop dramatically (as a square root of velocity). This is the &#;Achilles Heel&#; of a mechanical press drive, as applications that require lower speeds usually are deep draw and forming applications, which require higher energy for forming. As a result, the flywheel will begin to slow and eventually stall. Some stampers mistake this as lacking sufficient press tonnage, but in reality the application is exceeding the available energy at the current stroke rate.
3. How does available energy relate to speed on a servo press?
With a servo press, energy does not relate to press speed, since energy is not stored in a mechanical flywheel. Instead, a servo press draws energy either from the main line or from a separate energy-management system (EMS) that supplies the additional required energy for the application.
As press speed decreases, the available energy drops rapidly on a conventional mechanical press and increases with a servo press, as displayed on the accompanying graph.
Are you interested in learning more about Servo punching press? Contact us today to secure an expert consultation!